M数缩尺法旋翼颤振动力相似模型设计

本文以延-2复合材料桨叶旋翼为例,用M数缩尺法尝试设计了缩尺比为1/5的颤振相似模型。设计从旋翼颤振微分方程开始,应用π定理得出10个独立相似准则数,列出各有关物理量缩尺因子后进行模型结构设计,从而得出了若干有益的结论。     

针栓式喷注单元膜束撞击雾化混合过程数值模拟

为了全面认识针栓式喷注器喷雾场结构，基于自适应网格加密技术和分三相计算的PLIC VOF（Piecewise Linear Interface Calculation Volume of Fluid）方法对针栓式喷注单元膜束撞击雾化混合过程进行了仿真分析，通过对两路推进剂分别进行界面追踪，获得了膜束撞击雾化混合过程的详细结构特征，与高速摄影试验结果定性定量对比均吻合较好，验证了数值方法的准确性。以此为基础对膜束撞击的喷雾场结构、撞击变形过程、流场涡结构、雾化破碎典型特征及破碎后的雾化混合分布特征进行了识别分析，结果表明：膜束撞击形成了液束未穿透液膜和液束穿透液膜2种不同的喷雾扇结构。膜束撞击形成的喷雾扇呈"Ω"形，膜束同时发生弯曲变形和横截面变形。另外，膜束撞击同时受到正压和剪切应力作用，导致了一系列复杂涡流现象，使得相互作用增强，雾化混合均增强，这也是膜束撞击喷注构型优于膜膜撞击的本质原因。最后，还发现膜束撞击喷雾场液滴分布呈现分区结构特征，分别是液束控制主导的上雾化区、液膜控制主导的下雾化区及夹在中间的混合区，实际中应兼顾雾化特性和混合特性，选取中等动量比膜束撞击，这可为针栓式喷注器的理论研究和工程设计提供重要参考。     

Robust adaptive fault-tolerant control of a tandem coaxial ducted fan aircraft with actuator saturation

This paper is concerned with the robust adaptive fault-tolerant control of a tandem coaxial ducted fan aircraft under system uncertainty, mismatched disturbance, and actuator saturation. For the proposed aircraft, comprehensive controllability analysis is performed to evaluate the controllability of each state as well as the margin to reject mismatched disturbance without any knowledge of the controller. Mismatched disturbance attenuation is ensured through a structured H-infinity controller tuned by a non-smooth optimization algorithm. Embedded with the H-infinity controller, an adaptive control law is proposed in order to mitigate matched system uncertainty and actuator fault. Input saturation is also considered by the modified reference model. Numerical simulation of the novel ducted fan aircraft is provided to illustrate the effectiveness of the proposed method. The simulation results reveal that the proposed adaptive controller achieves better transient response and more robust performance than classic Model Reference Adaptive Control (MRAC) method, even with serious actuator saturation.     

Lift coefficient prediction at high angle of attack using recurrent neural network

In this paper, identification of dynamic stall effect of rotor blade is considered. Recurrent Neural Networks have the ability to identify the nonlinear dynamical systems from training data. This paper describes the use of recurrent neural networks for predicting the coefficient of lift (C_Z) at high angle of attack. In our approach, the coefficient of lift (C_Z) obtained from the experimental results (wind tunnel data) at different mean angle of attack θ_mean is used to train the recurrent neural network. Then the recurrent neural network prediction is compared with experimental ONERA OA212 airfoil data. The time and space complexity required to predict C_Z in the proposed method is less and it is easy to incorporate in any commercially available rotor code.     

Numerical study on flow fields and aerodynamics of tilt rotor aircraft in conversion mode based on embedded grid and actuator model

A method combining rotor actuator disk model and embedded grid technique is presented in this paper, aimed at predicting the flow fields and aerodynamic characteristics of tilt rotor aircraft in conversion mode more efficiently and effectively. In this method, rotor's influence is considered in terms of the momentum it impacts to the fluid around it; transformation matrixes among different coordinate systems are deduced to extend actuator method's utility to conversion mode flow fields' calculation. Meanwhile, an embedded grid system is designed, in which grids generated around fuselage and actuator disk are regarded as background grid and minor grid respectively, and a new method is presented for ‘donor searching' and ‘hole cutting' during grid assembling. Based on the above methods, flow fields of tilt rotor aircraft in conversion mode are simulated, with threedimensional Navier–Stokes equations discretized by a second-order upwind finite-volume scheme and an implicit lower–upper symmetric Gauss–Seidel(LU-SGS) time-stepping scheme. Numerical results demonstrate that the proposed CFD method is very effective in simulating the conversion mode flow fields of tilt rotor aircraft.     

出口轮毂形状对大型轴流风机性能影响的数值研究

针对某大型轴流风机设计了4种出口段轮毂匹配方案,采用数值模拟方法对比分析了4种方案下的风机特性和叶尖以及叶根流场结构.结果表明:出口轮毂形状的变化对该风机叶尖流场结构影响很小;该风机出口无轮毂时,在叶根区域出现约占20%叶高区域的分离流,损失严重,降低了工作效率;在相同的叶尖间隙下,风机效率随着出口轮毂扩压角的减小而提高;在风机出口增加一个匹配的平直轮毂或收缩轮毂可使叶根分离涡后移,分离区域减小至5%叶高以下,同时可使该风机效率至少提高2个百分点.     

高压涡轮转子叶片内部气流组织方式研究

为了获得涡轮转子叶片内部冷却结构的冷却性能,采用气热耦合计算的方法分析了在相同冷气总量条件下3种不同的气流组织方式对叶片冷却效果的影响,并选择其中相对优化的冷却结构进行了转速对进气压力和综合冷却效率的影响研究。结果表明,B型结构叶片气流组织较为合理,表面温度较为均匀,整体冷却效率得到有效提高;哥氏力和离心浮升力的存在导致冷却气流发生相应偏转,前缘滞止线随转速增加由压力面向吸力面偏移,同时前缘气膜出流随转速发生变化,随着转速增大,压力面综合冷却效率提高,吸力面综合冷却效率下降。     

周向平均方法在某风扇/增压级分析中的应用简

 通过对三维（3D）Navier-Stokes方程进行周向平均,得到了通流模型的控制方程,对其采用时间推进有限体积方法进行数值求解。为实现风扇/增压级在设计初期的快速性能评估,考察了周向平均方法在风扇/增压级分析中的准确性。分别利用NUMECA三维数值模拟软件和周向平均通流模型（CAM）对某高通流风扇/增压级进行了性能分析,从对比结果来看,周向平均通流模型在近设计点给出了与三维数值模拟十分接近的特性参数,最大误差不超过2.0%。在风扇转子中,由于周向平均通流模型能捕获通道激波,其物理本质与三维平均结果有所区别,因此径向参数分布与三维有所差异。而在亚声速流动下的增压级及外涵道各叶片排出口参数的径向分布与三维数值模拟结果都能很好地吻合。     

转子-支承耦合结构的模型修正研究

在转子-支承耦合结构的动力学分析过程中,结构模态参数计算结果与实验测试结果往往存在较大差异。针对此问题,应用优化算法对结构动力学模型进行修正,使计算模型能更准确地反映结构特性。建立由梁单元、盘单元、弹性支承单元组成的结构动力学有限元模型;选择优化目标函数、设计参数,并对各参数进行灵敏度分析。应用粒子群算法对选取的设计参数进行优化,得到最优模型。利用转子-滚动轴承实验器进行验证,结果表明,方法能够有效地实现转子-支承耦合结构的动力学模型修正,修正后模型更接近实际结构。     

基于某型发动机发展 STOVL 动力性能方案研究

短距起飞/垂直降落（STOVL）飞机由于其优越的作战性能,受到了世界航空大国的高度重视。通过借鉴目前最先进的 STOVL 动力 F135- PW -600发动机技术发展思路,研究了基于国内某型发动机改 STOVL 动力方案时,主发动机与升力风扇之间的匹配和约束关系。研究结果表明：随着升力风扇压比和流量的增加,主发动机升力减小,升力风扇升力增加;同一主发动机状态下,升力风扇流量越大,发动机前后升力平衡的升力风扇压比越小,总升力越大;主发动机性能越高,发动机前后升力平衡的升力风扇压比和流量越大,发动机总升力也越大。